You use a router table by mounting the router under the tabletop, setting the bit height and fence position, and feeding the workpiece against the bit's rotation. The one rule that governs everything else: feed from right to left across the front of the table so the cutter's rotation pushes the wood into the fence. Skip that and the bit grabs the stock and throws it.

A router table turns a handheld router into a small shaper. The motor hangs fixed under the top, the bit pokes up through a plate, and a fence gives you a straight edge to register against. That arrangement solves two problems handheld routing can't: it holds the machine still so both your hands control the wood, and it lets you run narrow or small parts past a cutter safely.

The trade-off is setup time. Every cut on a table starts with two adjustments β€” bit height and fence position β€” and getting those wrong is where most ruined workpieces and most kickback incidents come from. The steps below run in the order you'd actually work: machine first, then geometry, then the cut itself.

Mount the Router and Set Up the Plate Before Any Cut

Start by matching the plate to the router. Most router tables use a plate with a centered, interchangeable insert ring, and the opening in that ring is sized to the bit. Porter-Cable and DeWalt plunge routers, and the common Bosch and Makita fixed-base models, each have their own mounting-hole pattern, so confirm your base fits the plate's hole spacing before you tighten anything.

Remove the router's base plate and sub-base if the table plate replaces them. Drop the motor into the plate from below, align the mounting holes, and snug the screws finger-tight first. A plate that isn't seated flush creates a lip at the bit opening, and that lip catches the workpiece edge on every pass.

Set the plate flush with the tabletop using its leveling screws. Run a straightedge across the top in both directions; any rocking means one corner is proud. A plate a few thousandths of an inch high is worse than one slightly low, because the wood tips into the cutter instead of gliding over it.

Check that the collet and bit sit clear of the insert ring at full plunge. If the ring opening is smaller than the bit's cutting diameter, swap to the next size up β€” most plate kits ship two or three ring sizes for exactly this reason. Tighten the plate screws only after leveling is confirmed.

Read the Feed Direction Correctly or the Bit Will Throw the Wood

A router bit spins clockwise viewed from above. At the fence side, that rotation drives the cutter toward you on the right-hand side of the bit and away from you on the left-hand side. Standard table routing therefore sends the workpiece right to left along the fence, so the bit's cutting edge opposes the feed and takes a clean shaving.

Feed the other way, left to right, and the bit climbs through the wood. On a table that climb cut pulls the stock forward at a speed you can't control. Narrow offcuts and end-grain cuts are the worst cases, because there's little mass to damp the grab.

The same logic explains why the fence side matters. With the bit between you and the fence, the workpiece registers on the fence and the cutter bites into the edge facing the fence. With the bit on the far side of the fence β€” a "back-routing" setup used for pattern work β€” the geometry inverts and the safe direction flips. Confirm which side of the bit your fence sits on before you commit a board to the cutter.

Edge cases break the rule honestly. Pattern routing with a bearing-guided bit against a template can be done as a climb cut deliberately, in light passes, to avoid tearout on figured wood. That's a controlled technique with a bearing carrying the load, not a license to feed backwards on a fence-guided straight cut.

Set Bit Height With the Workpiece in Place, Not by Eye

Bit height is the single adjustment that decides whether a groove is the right depth or a rabbet is the right width. Set it with the stock on the table, not with the router upside down, because the table surface is your zero.

For a groove or dado, measure from the tabletop to the top of the cutter with a rule or a depth gauge, then subtract nothing β€” the exposed cutter height equals the groove depth. For a rabbet, the exposed height equals the rabbet's shoulder depth. For an edge profile like a roundover or ogee, the height is set so the bearing or the profile's shoulder lands flush with the top face of the stock.

Lock the plunge mechanism or the fixed-base adjustment after setting height, then re-check with a test cut on scrap of the same thickness. Bit height drifts on plunge routers that aren't locked, especially during a long run of parts, and a groove that deepens halfway through a set of shelves is a scrap pile.

Work in small increments. Raising a bit a sixteenth of an inch at a time and testing beats dialing in a full profile and discovering it's too deep on the first board. On a fixed-base router mounted under the table, height changes come from the base's adjustment ring or a router lift; a lift with a graduated dial makes repeatable height changes far easier than reaching under the table.

Install and Set the Fence for the Cut You're Making

The fence does two jobs: it controls depth of cut in the direction perpendicular to the bit, and it gives the workpiece a straight reference face. Its position relative to the bit's centerline sets how much of the cutter engages the wood.

For an edge profile, set the fence so the bit's bearing or profile meets the stock edge cleanly. For a groove in the middle of a board, the fence offset from the bit centerline sets the groove's distance from the board edge, and the bit height sets its depth. For a rabbet, the fence plus the exposed bit height together define both legs of the cut.

Many fences come in two halves that slide independently. Open the gap around the bit to just clear the cutter, then close the halves so each one supports the stock right up to the cutting edge. An open gap wider than necessary lets thin stock dip into the opening.

Square the fence to the table's miter slot and to the bit's axis. A fence that's a degree or two off produces a taper on every edge you run, and the error compounds across a set of parts. Check with a combination square against the slot, then confirm with two test cuts on parallel-edged scrap.

Match Depth of Cut to Bit Diameter on Every Pass

The most common table mistake isn't a wrong setup β€” it's taking too much in one pass. Rule of thumb used across the trade: a cut no deeper than the bit's cutting diameter, and for hardwoods or large-diameter panel bits, half the diameter per pass.

A 1/2-inch straight bit removes up to about 1/2 inch in a pass in softwood, but a 1/2-inch-deep pass in white oak with the same bit will burn and kick. A raised-panel bit with a 3-inch cutter wants multiple staged passes, each one creeping up on the final profile. The bit's own instructions from the maker give the maximum cut for that specific geometry; follow them over any general rule.

Light passes cost time but protect the cutter and your hands. A three-pass groove in hardwood takes maybe a minute more than a single pass and leaves a cleaner wall with less burn. Burning comes from a cutter rubbing rather than slicing, and a shallow pass at a steady feed rate slices.

Stacking passes also makes the last pass a cleanup cut. Leave a few thousandths of an inch for the final full-depth pass, and the groove walls come out uniform along the whole board.

Build a Starter Pin and Use Push Blocks for Narrow Stock

Small parts are where table routing hurts people. A starter pin β€” a smooth pin threaded into the table just in front of the bit β€” gives narrow stock a pivot point to register against as it enters the cut. You press the work against the pin, swing it into the bit, and the pin keeps the stock from being pulled forward.

Push blocks with a heel or a bird's-mouth profile keep your hands above and behind the cutter. For stock narrower than about 3 inches, use a push block on the trailing end and a featherboard holding the stock to the fence. Featherboards aren't a substitute for hand position; they're an addition to it.

Set the bit guard or at least the fence gap so your fingers can't reach the cutter. The opening around the bit should be no wider than the work requires. A transparent guard on the fence lets you see the cut and keeps debris from flying at your face.

Never reach over or past a spinning bit, even with the router switched off at the switch β€” the motor coasts. Use a push stick to clear offcuts, and clear chips with a brush or a vacuum, not fingers.

Use a Miter Gauge and Featherboards to Control the Workpiece

Crosscut work, end-grain profiles, and cutting tenons on the ends of rails all want the workpiece held square to the bit. The miter gauge in the table's slot does that, sliding the stock past the cutter at a set angle while the fence stays out of the way or is removed.

Featherboards hold the stock against the fence through the cut. A horizontal featherboard presses the work toward the fence; a vertical one holds it down to the table. Both should be set just behind the bit's leading edge, angled so the fingers flex against the direction of feed.

Don't set a featherboard so it pinches the stock before the bit or after it. Pinching ahead of the bit can bind the stock; pinching too far back does nothing. The sweet spot is directly alongside the cutter, with light pressure.

Keep the miter gauge's slot clean and waxed, and check that the gauge's face is square to its bar. A gauge that's off by a degree puts a taper on every tenon cheek, and the error is invisible until you assemble the joint.

Cut an Edge Profile in Three Passes on a Test Piece

Set up a roundover on scrap of the same species and thickness as the real stock. This is the sequence to run before touching a finished board.

1: Set the bit height so the bearing rides on the stock's top face, with the profile's shoulder flush. 2: Set the fence so the bearing contacts the stock edge and the cutter takes a light initial bite. 3: Run one test pass at full depth on scrap. Check the profile's shoulder for a step or a gap. 4: Adjust height by half the visible step, then test again. 5: On the real stock, take the first pass at about half depth, then a second at full depth, then a final cleanup pass.

If the finished profile shows a line where the bearing meets the wood, the bit height is off fractionally β€” the bearing is riding proud or sunk. If the profile tears out on end grain, the bit is dull or the pass is too heavy.

End-grain tearout on a roundover is the failure case worth preparing for. Run the end-grain passes first, before the long-grain passes, so the long-grain cut cleans up any blowout at the corners. If tearout persists, back the exit edge with a sacrificial block clamped to the stock.

Run a Raised-Panel Bit Safely With Staged Passes and Backing

Raised-panel bits are the biggest cutter most home shops run on a table, and they demand the most caution. A panel-raising bit commonly measures 3 inches or more across, and at router speeds of 20,000 rpm and up a cutter that size stores a lot of energy. The maker's maximum speed for the specific bit governs β€” large-diameter panel bits are often rated for lower rpm than small straight bits, and the router's speed dial should be set accordingly.

Set the bit height so the panel's tongue thickness matches the groove in the frame. Run the panel on edge, standing on its long edge, with the fence set so the cutter profiles the edge. Use a tall auxiliary fence face for panels, because an 18-inch-tall panel needs fence support well above the standard fence height.

Feed the panel slowly and steadily, keeping it flat on the table and tight to the fence. A large cutter wants a slower feed than a small one; pushing too fast stalls the motor, and a stalled cutter in a deep cut is a kickback waiting to happen. Take the profile in two or three staged passes, raising the bit between passes.

Back the panel's exit edge with a sacrificial board clamped in place, especially on cross-grain cuts. The cutter exits the wood at the far corner of a panel, and that's where splintering starts. A backing board takes the blowout instead of the finished panel.

Maintain Bits, Belts, and the Table Surface for Repeatable Results

A dull bit on a router table burns wood, and burn is a symptom of rubbing rather than cutting. It also increases feed resistance, which raises the kickback risk. Sharpen or replace bits when they stop leaving a clean, glassy cut on a test pass, or when you can feel a burr on the cutting edge with a fingernail.

Clean the table surface and the plate with a wax or a dry lubricant made for machine tops. Pitch and dust build up on the surface and increase drag on the workpiece, especially on long boards. Wipe down after each session rather than letting chips pack into the miter slot.

Check the router's belt or coupling if the motor is a separate unit, and check the collet for wear. A worn collet lets the bit creep in the chuck under load, which changes bit height mid-cut. Re-tighten the collet with the router's own wrench, and never use a collet that shows scoring or galling.

Inspect the plate's leveling screws and the fence's locking knobs periodically. A fence that drifts under feed pressure shows up as a taper on one side of the cut, and it's easy to blame the bit before checking the fence lock.

FAQ

Can I use a router table without a fence?

Yes, for freehand pattern work with a bearing-guided bit, but every straight cut needs a fence or a miter gauge for registration. Running a straight bit against a workpiece with nothing to register against invites the cutter to grab and pull the stock. Even bearing-guided pattern work benefits from a starter pin and a firm grip.

Is it safe to climb cut on a router table?

Deliberate climb cuts, feeding left to right, are used in light passes on figured wood or for pattern work to control tearout. The bearing or template carries the load in those cases. Climb cutting a fence-guided straight cut with a large bit is a different matter β€” it's the classic kickback scenario, and it's not a technique to practice on finished stock.

What's the maximum depth of cut for one pass?

A common trade rule limits a pass to the bit's cutting diameter, and to roughly half the diameter in hardwoods with large profile bits. The bit maker's own maximum cut specification overrides any general rule, because cutter geometry and flute count change what a specific bit can take. Staged passes are the safe default.

How do I stop burning on a router table cut?

Burn usually means the cutter is rubbing rather than slicing, so check three things: bit sharpness, feed rate, and depth of cut. A dull bit, an overly slow feed, or a pass that's too heavy all produce burn. A cleanup pass at full depth with a steady feed is the fix once the setup is right.

Do I need a router lift to use a table?

Not strictly. A fixed-base router in a table adjusts height through its base ring, and a plunge router through its plunge mechanism, both reachable from under the table. A lift makes height changes much more repeatable and lets you adjust from above the table, which speeds up bit changes and staged passes.

How do I cut a groove a set distance from the board edge?

Set the fence's distance from the bit's centerline to the groove's distance from the edge, and set the bit height to the groove depth. Both adjustments interact, so test on scrap of the same thickness first. The fence controls the position and the bit height controls the depth β€” keep them separate in your head.

What size router does a table need?

Table routing favors 1/2-inch-collet routers with enough mass and power for large bits; a plunge router around 2 horsepower or more handles panel and large profile bits. A trim router in a table works for light edge profiles but struggles with big cutters and deep passes. The bit's shank size and the router's collet capacity need to match.

Why does my workpiece drift away from the fence?

Drift usually comes from feed direction, fence alignment, or a featherboard set in the wrong place. Feeding against the rotation is essential; a fence that's out of square produces taper; and a featherboard angled too far ahead or behind the bit does nothing useful. Check all three before blaming the bit.