The 2000 Jaguar S-Type used two different EGR pipe diameters depending on which engine was under the hood: 3.0 V6 cars took a pipe with roughly 18 mm (about 0.71 in) outside diameter plumbing, while the 4.0 V8 used a distinctly larger pipe in the 22 mm (about 0.87 in) range. That split is exactly why parts listings for this model year get confusing. Jaguar never published a single "S-Type EGR pipe diameter" because there wasn't one.
What the reader usually needs is narrower than that: the thread size or fitting diameter on the pipe they're holding, or the size of the replacement they're about to order. Those are two separate measurements, and mixing them up is the most common way people buy the wrong part for a 2000 S-Type. Confirm the actual dimension on your own pipe or on the Jaguar parts catalogue for your VIN before ordering, since I can't verify a specific aftermarket part number for you.
Why the 2000 S-Type has two EGR pipe sizes at all
Model year 2000 was a transition point for the S-Type. The car launched for 1999 with the 3.0-litre AJ-V6 and the 4.0-litre AJ-V8, and both engines carried exhaust gas recirculation hardware on US-market cars because federal emissions rules required it. The two engines came from different design families, so their EGR plumbing wasn't shared.
The V6's EGR system routes exhaust through an external pipe from the exhaust manifold area up to the EGR valve mounted near the intake. The V8 uses its own layout with a different valve position and a larger-diameter feed pipe. That physical difference is the root of the diameter question, and it's why a parts counter clerk will ask for your engine size before anything else.
Jaguar's own parts catalogue splits EGR components by VIN and engine, not by model year alone. Any listing that says "fits 2000 S-Type" without naming the engine should be treated as incomplete. According to Jaguar's published parts data, the two engines share body panels and interior trim far more readily than emissions hardware.
One more wrinkle: the supercharged S-Type R arrived later, and its EGR arrangement isn't relevant to a standard 2000 model year question. If you're working on a 2000 car, you have either the 3.0 or the 4.0, and nothing else. The table below lays out the split in plain terms.
| Engine | Typical EGR pipe OD ballpark | Fitting type | Why it matters |
|---|---|---|---|
| 3.0 V6 (AJ-V6) | ~18 mm / 0.71 in | Threaded flare fitting at valve | Smaller pipe, tighter bends near manifold |
| 4.0 V8 (AJ-V8) | ~22 mm / 0.87 in | Threaded fitting, larger bore | Higher flow area for the bigger engine |
| S-Type R (later) | Not applicable to 2000 MY question | β | Supercharged variant, different hardware |
Treat those millimeter figures as working ballparks, not a published Jaguar spec sheet. The reliable path is to measure your pipe or pull the number from the parts catalogue with your VIN in hand.
How to measure your EGR pipe before you order
Measure the pipe you have, not the pipe you think you need. A caliper on the outside diameter tells you the physical size, but the number that actually matters for ordering is usually the thread or fitting size at each end. Do both if you can.
1: Let the engine cool completely, then locate the EGR valve on the intake side and trace the metal pipe from it toward the exhaust side. 2: Clean the pipe ends with a rag so carbon buildup doesn't skew your reading. 3: Use a digital caliper across the outside diameter at a straight section, not at a bend or a crimp. 4: Measure the threaded fitting at the valve end with a thread pitch gauge or by matching against known nuts. 5: Write down both numbers and your VIN, then cross-check against the Jaguar parts catalogue or a supplier that lists by engine code.
If the caliper reading lands between the two ballpark figures β say 20 mm β you're probably measuring over rust scale or a heat shield edge. Clean the surface and re-measure before you conclude anything.
Failure case worth knowing: people often order by photo. An eBay or marketplace listing showing a "2000 S-Type EGR pipe" may be a V8 pipe photographed alongside a V6 car. The photo looks right, the fitment note says "S-Type," and the pipe arrives with the wrong fitting. If the listing doesn't state the engine displacement explicitly, ask the seller before paying. A wrong pipe that threads halfway is worse than no pipe, because you'll chase a vacuum leak for a week.
V6 versus V8: what actually differs beyond diameter
Diameter is the headline, but the two EGR pipes differ in routing, mounting brackets, and heat shielding as well. The V6 pipe snakes around a tighter engine bay with more bends, which is one reason its diameter stays smaller β tighter bends in a large-bore pipe are harder to form and more prone to cracking.
The V8 pipe runs a more direct path and carries a larger bore because the bigger engine moves more exhaust volume. Its fittings are correspondingly larger. If you're swapping parts between a V6 and V8 car, nothing about the EGR pipe is interchangeable.
Bracket hardware is the quiet difference. The V6 pipe uses a specific standoff bracket bolted to the block, and that bracket is frequently missing on used cars because a previous owner removed it during a repair and never reinstalled it. A pipe without its bracket will crack at the fitting within a few thousand miles from vibration. When you buy a replacement, confirm the bracket is included or transfer your old one.
Heat shielding matters too. The V8 pipe sits closer to the exhaust manifold on some layouts and relies on a stamped shield to keep the EGR valve from cooking. If your replacement pipe arrives without the shield provision, don't bolt it up and hope. This is the kind of detail that separates a correct repair from a comeback.
The symptom that sends most owners looking for this number
Most people searching for the EGR pipe diameter on a 2000 S-Type aren't doing a parts lookup for fun. They have a check engine light with a P0401 code β "EGR flow insufficient" β and they've traced it to a cracked or rusted pipe. That code is the single most common trigger for this repair on these cars.
A cracked EGR pipe behaves like a vacuum leak that only appears under certain conditions. You might notice a rough idle, a faint hiss from the engine bay when cold, or a stumble on light throttle. The P0401 sets because the powertrain control module commands EGR flow, sees the expected manifold pressure change doesn't happen, and flags the circuit.
Diagnosis order matters. Before you buy any pipe, confirm the EGR valve itself isn't stuck, the vacuum supply is intact, and the passages aren't carbon-clogged. A plugged EGR passage in the intake manifold produces the same P0401 and costs nothing but time to clean. Chasing the pipe when the real fault is a blocked port wastes money.
If the pipe is cracked, replacement is the fix. If it's merely carbon-fouled at the fitting, cleaning may restore flow. The diameter question only becomes urgent once you've confirmed the pipe itself is the failed component, and at that point you need the right size for your engine.
Thread and fitting size: the spec that decides whether it bolts up
The outside diameter of the pipe tube and the size of the threaded fitting are two different numbers, and the fitting is the one that stops a wrong part from installing. On these cars the EGR pipe connects with threaded flare fittings rather than slip-on hose clamps, so a half-millimeter error in thread pitch means it won't seal.
Jaguar used metric fittings throughout this era. A supplier listing in fractional inches is a red flag unless it also gives the metric equivalent. When you're comparing a used pipe to a new one, thread the old fitting onto the new pipe by hand before installing anything. If it binds after two turns, the thread is wrong and no amount of torque will fix it.
Thread sealant is a judgment call. Copper anti-seize on the threads helps future removal, but it won't seal a damaged flare. The flare does the sealing; the threads do the clamping. If the flare face on the pipe or the valve is pitted, replace the component rather than trying to seal it with paste.
Torque values for these fittings aren't something to guess. Consult the Jaguar service information for your engine before tightening, because overtightening a flare fitting crushes the sealing surface and creates the leak you were trying to fix. A torque wrench is cheap compared with a replacement EGR valve.
What a replacement pipe costs and how long the job takes
Plan on a parts cost in the low hundreds of dollars for an OEM-equivalent pipe and a couple of hours of labor for a careful DIY job on the V6, longer on the V8 if the pipe is buried. Independent shop labor at typical rates will often exceed the parts cost. These are planning ranges, not quotes β confirm current pricing with your supplier.
Time computation matters more than the dollar figure for most owners. On the V6, the pipe is reachable from the top with the engine cover off, and the fittings usually break free with a flare nut wrench. On the V8, access can require moving more hardware, which is where the labor hours climb. If a shop quotes you a flat rate, ask whether it's based on the V6 or V8 procedure, because they aren't the same.
The hidden cost is the snapped fitting. A rusted flare nut that rounds off turns a two-hour job into an EGR valve replacement plus a pipe. Soak the fittings in penetrating oil the night before, use a proper flare nut wrench rather than an open-end, and accept that a stuck fitting may need heat.
Do the math before you start: parts plus your time versus a shop quote. If the fittings are badly rusted and you don't own a torch, the shop quote often wins. If the fittings are clean, the DIY job is straightforward and the diameter question is the only real research you need to do.
Common mistakes when buying this pipe
The first mistake is buying by model year alone. "2000 Jaguar S-Type" describes two different cars under the hood, and the EGR pipe is one of the parts where that difference bites. Always state the engine displacement in any order.
The second is trusting a photo over a fitment note. Marketplace and auction listings recycle photos across engine variants, and the picture of a shiny new pipe tells you nothing about the thread size. Ask for the part number stamped on the pipe or the engine code it came from.
The third is skipping the bracket. A replacement pipe installed without its mounting bracket will fail at the fitting, usually within a season of driving. If the new pipe doesn't include the bracket, move yours over before installation, and replace it if it's cracked.
The fourth is ignoring the EGR valve while the pipe is off. If the valve is carboned up or the pintle is sticky, you'll be back under the hood within months. Clean or replace the valve while you have access. The pipe is the easy part; the valve is what actually controls flow.
When the diameter question is the wrong question
Sometimes the pipe isn't the problem at all. A P0401 on a 2000 S-Type can come from a failed differential pressure feedback sensor, a cracked vacuum line to the EGR valve, or carbon blocking the intake passage. In those cases, knowing the pipe diameter gets you nowhere because you don't need a pipe.
Work the diagnosis in order: check for vacuum at the valve, command the valve with a scan tool and watch for a change in manifold pressure, then inspect the pipe and passages. Only when the pipe is confirmed cracked or leaking does the size matter.
If you've replaced the pipe and the code returns, the fault is upstream or downstream of the pipe, not in it. A smoke test on the intake tract will find a leaking vacuum line in minutes. Don't buy a second pipe hoping the first one was the wrong size.
One edge case: a 2000 S-Type that's had an engine swap or a replacement head from a different year can have mismatched EGR hardware. If the car's history is unknown, measure what's actually installed rather than trusting the VIN's original build sheet. The VIN tells you what left the factory; it doesn't tell you what a previous owner bolted on.
FAQ
Does a 2000 Jaguar S-Type 3.0 and 4.0 use the same EGR pipe?
No. The V6 and V8 use different pipes with different diameters and fittings, and they don't interchange. The V6 pipe is the smaller of the two, roughly 18 mm outside diameter, while the V8 pipe runs around 22 mm. Always order by engine displacement and confirm the fitting size before purchase.
What is the actual thread size on the S-Type EGR pipe fitting?
Jaguar used metric flare fittings on these cars, and the thread size differs between the V6 and V8 pipes. The exact pitch isn't something to guess from a forum post β check the Jaguar parts catalogue for your VIN or measure the fitting with a thread pitch gauge. A fitting that threads by hand for two turns is the right one.
Will a wrong-diameter EGR pipe cause a check engine light?
Yes, and it usually shows up as P0401, insufficient EGR flow. A pipe with the wrong fitting won't seal, so the system can't meter exhaust gas correctly and the powertrain control module flags the fault. The light may take a few drive cycles to set, which is why some people install a wrong pipe and think it worked.
Can I drive with a cracked EGR pipe on a 2000 S-Type?
Short distances to a shop are usually tolerable, but prolonged driving with a cracked pipe can cause a rough idle, poor fuel economy, and increased emissions. On some engines it can also let unmetered air into the intake and skew fuel trims. Fix it promptly rather than treating it as a cosmetic issue.
How much does a replacement EGR pipe cost for this car?
Parts typically run in the low hundreds of dollars for an OEM-equivalent pipe, and shop labor often exceeds the parts cost because of access differences between the V6 and V8. Confirm current pricing with your supplier, since these figures move with the market and I can't verify today's numbers.
Is the EGR pipe the same on a 2000 S-Type and a later S-Type R?
No. The supercharged S-Type R uses different emissions hardware, and its EGR arrangement isn't shared with the standard 2000 model year cars. If you're working on a 2000 S-Type, you have either the 3.0 V6 or the 4.0 V8, and the R parts don't apply.
What else should I replace while the EGR pipe is off?
Inspect and clean the EGR valve, check the vacuum supply line for cracks, and confirm the intake passage isn't carbon-blocked. Replace the pipe's mounting bracket if it's missing or cracked. Doing these while the pipe is off saves you from a second teardown if the code returns.
Can I measure the pipe diameter without removing it?
Yes, on most cars you can reach a straight section of the pipe with a caliper from above once the engine cover is off. Clean the surface first so rust scale doesn't inflate the reading. If access is too tight on the V8, measure at the fitting end where the pipe meets the valve.