The three teenagers used chitosan, a sugar-based polymer derived from shellfish shells, to create a powder that pulls microplastics out of water. The team — Irish students Fionn Ferreira and his collaborators — demonstrated that chitosan combined with a magnetic iron compound could bind plastic particles and then be removed with a magnet. The key condition is that the powder works best in controlled, small-scale tests; it is not yet a municipal water treatment product. What follows explains the chemistry, the tests, the limits, and what a reader should realistically expect from this innovation.

What Is Chitosan and Why Does It Grab Microplastics

Chitosan is a polysaccharide made by deacetylating chitin, the structural material in crab, shrimp, and lobster shells. In plain terms, it is a long chain of sugar-like units studded with amine groups. Those amine groups carry a positive charge in slightly acidic water, which is the whole trick behind the powder's behavior.

Microplastic particles in water tend to carry a negative surface charge, especially in freshwater with dissolved organic matter. When positively charged chitosan meets negatively charged plastic, electrostatic attraction pulls them together. The plastic particles clump into larger aggregates in a process called coagulation-flocculation, and those clumps settle or can be filtered out.

This is not a new discovery in water treatment — chitosan has been used for decades to clarify drinking water and treat wastewater. What the teenagers did was apply it specifically to microplastics and pair it with a recoverable magnetic component. The novelty sits in the combination and the small-scale demonstration, not in the raw material itself.

Chitosan is biodegradable, non-toxic in food-grade form, and produced commercially from shellfish waste. That waste-recycling angle is part of why the project attracted attention. The global chitosan market was valued in the hundreds of millions of dollars according to industry analyses published before 2024, and it is already sold as a water-treatment flocculant under names like chitosan flakes or chitosan powder.

The Three Teenagers and the Project That Put Chitosan on the Map

The project most closely associated with this keyword is the work of Fionn Ferreira, an Irish student from Schull, County Cork. Ferreira developed a method using a magnetic liquid — a ferrofluid — to extract microplastics from water, and he won the 2019 Google Science Fair Grand Prize at age 18 for that work. His method used magnetite, an iron oxide, suspended in a carrier fluid.

Separately, other student teams have combined chitosan with magnetic particles to make a recoverable powder. The version described in popular coverage uses chitosan as the binding agent and iron oxide nanoparticles as the magnetic handle. After the powder binds plastic, a magnet pulls the whole aggregate out of the water.

The exact identity of "three teenagers" varies across reports, and readers should treat any single name list with caution. Ferreira's publicly documented project is the best-attributed anchor. He estimated his method could remove about 87 percent of microplastic particles in his own tests, according to his project documentation and interviews reported in 2019.

What is verifiable: a student project using magnetic extraction of microplastics won major science fair recognition, and chitosan-magnetite composites are a real research area with published studies in journals such as Water Research and Journal of Hazardous Materials before 2024. What is not verifiable here: a specific three-person team name, a specific powder product for sale, or a commercial price.

How the Powder Actually Works in Four Stages

The removal process follows a predictable sequence that any reader can follow without a chemistry background. Understanding each stage explains both the powder's promise and its practical limits.

1: Dispersion. The chitosan-based powder is stirred into a water sample. The powder disperses and its amine groups begin interacting with particle surfaces. 2: Binding. Positively charged amine groups attach to negatively charged microplastic surfaces. Hydrogen bonding and hydrophobic interactions add to the electrostatic attraction. 3: Aggregation. Bound particles clump into larger flocs. Chitosan's long molecular chains bridge between particles, which is why it outperforms simple salt-based coagulants on fine particles. 4: Magnetic separation. The iron oxide component lets a magnet collect the flocs. Without the magnetic handle, the flocs would need settling tanks or filters.

If the pH drifts above about 6.5, chitosan's amines lose their positive charge and binding efficiency drops sharply. That failure mode is the single biggest practical constraint and rarely appears in upbeat coverage. A user working with hard, alkaline water would need to acidify first, adding a step and a cost.

The Test Results and What the Numbers Actually Mean

Ferreira's documented tests reported roughly 87 percent removal of microplastic particles across a range of plastic types, according to his Google Science Fair project materials. That figure came from small-scale, controlled samples — not from a flowing river or a wastewater plant.

Published academic work on chitosan-magnetite composites reports removal efficiencies in the 80–95 percent range for microplastic spheres in laboratory conditions, depending on particle size, dosage, pH, and contact time. Studies in Water Research before 2024 documented these ranges. Smaller particles and lower doses consistently reduce efficiency.

The gap between lab and field matters. Real water contains dissolved organic matter, competing ions, and varying pH. Each of those interferes with binding. A 2023 review in Environmental Science & Technology noted that most microplastic removal studies use pristine, uniform spheres that do not resemble weathered environmental plastic.

So the honest read: the powder works in principle and performs well in clean lab samples. Scaling to a river or a treatment plant requires pretreatment, dose optimization, and a plan for the collected sludge. A reader should not expect a spoonful to clean a pond.

How It Compares to Existing Microplastic Removal Methods

Water utilities already remove microplastics, mostly as a side effect of conventional treatment. Coagulation with aluminum or iron salts, sedimentation, and filtration together capture a large share of larger microplastics. The chitosan powder's edge is biodegradability and magnetic recovery, not raw removal rate.

Method Typical removal (lab) Recoverable? Residual chemical risk Practical maturity
Chitosan-magnetite powder 80–95% Yes, via magnet Low, biodegradable Lab and pilot only
Aluminum sulfate coagulation 70–90% No Sludge with metal salts Mature, municipal
Iron chloride coagulation 75–90% No Sludge with metal salts Mature, municipal
Membrane filtration (MF/UF) >95% N/A Fouling, cleaning chemicals Mature, high cost
Magnetic nanoparticle alone 70–90% Yes Nanoparticle release concern Research stage

The comparison row most coverage skips: membrane filtration beats every coagulation method on removal rate but costs far more per cubic meter and fouls quickly. Chitosan's realistic niche is as a low-cost, biodegradable coagulant aid, not a replacement for membranes. A utility choosing between them would weigh sludge disposal costs against membrane capital costs — a calculation no student project has published.

The pH Problem and Other Failure Cases

Alkaline water is the most predictable failure. Chitosan dissolves readily in dilute acid but becomes insoluble and largely inactive above pH 6.5 to 7. Most natural surface waters sit in that range or above, which means field deployment needs pH adjustment. That is a real operating cost rarely mentioned in popular summaries.

High turbidity is another edge case. In water loaded with sediment, the powder binds to clay and organic particles before it reaches microplastics. Efficiency collapses because the binding sites get used up on the wrong targets. Pretreatment to remove bulk sediment is essentially mandatory.

Nanoparticle shedding is a concern regulators would raise. If the iron oxide component is nanoscale, some fraction could remain suspended after magnetic collection. Published research flags this as an unresolved question for environmental release. A commercial product would need filtration verification, not just a magnet pass.

Finally, the collected sludge needs a destination. Microplastic-laden flocs are a waste stream. Incineration, landfill, or further processing all carry cost and regulatory requirements. The powder solves the separation problem but creates a disposal problem, and no coverage of the student project addresses that.

What It Would Take to Deploy This at Scale

The path from a science fair demonstration to a treatment plant runs through dose optimization, continuous-flow testing, and regulatory approval. Each stage adds cost and time. A rough sequence would start with bench-scale flow tests, then pilot skids at a wastewater plant, then permitting.

Dose matters economically. Chitosan typically requires a dose in the range of a few milligrams per liter for coagulation, according to water-treatment literature. At municipal flow rates of millions of liters per day, that translates to kilograms of chitosan daily — and chitosan prices fluctuate with shellfish supply.

The magnetic recovery step adds equipment. Magnetic separators exist in mining and food processing, adapted versions would be needed. Capital cost for a small pilot unit is plausibly in the tens of thousands of dollars, though no verified figure for this specific application exists publicly; confirm with equipment vendors.

Regulatory approval would hinge on whether the treated water meets drinking-water standards and whether residual chitosan and iron are within limits. Chitosan already has food-grade approvals in several jurisdictions, which helps, but each country sets its own rules. Check the relevant environmental agency before assuming approval.

What Readers Should and Should Not Expect From This Innovation

Expect a promising, low-cost coagulation chemistry with real lab evidence behind it. The core mechanism — positive chitosan binding negative plastic — is well-established. Published composites of chitosan and magnetite do remove microplastics in controlled tests at rates in the 80–95 percent band.

Do not expect a consumer product you can buy to purify your tap water. No verified commercial chitosan-microplastic powder exists for household use as of the reference date. Anyone selling one should be treated with suspicion, and readers should check for independent lab verification before buying.

Do not expect this to solve ocean plastic. Removal at the source — wastewater treatment — is the realistic application. Once microplastics reach open water at low concentrations, the dose economics become unfavorable compared with preventing the release in the first place.

Expect the science to keep developing. Chitosan modifications, magnetic composites, and hybrid coagulants are active research areas. The student projects lit a spark, and the underlying chemistry is sound. The commercial products, whenever they arrive, will come from water-treatment companies, not science fairs.

FAQ

Did the teenagers invent chitosan?

No. Chitosan has been used as a water-treatment flocculant since at least the 1990s and is produced commercially from shellfish waste. The students' contribution was applying it to microplastics and pairing it with magnetic recovery in a small-scale demonstration. Credit for the material belongs to the polymer chemistry field, not the student team.

How much microplastic does the powder actually remove?

Lab tests on chitosan-magnetite composites report 80–95 percent removal for plastic spheres, with Ferreira's own project reporting about 87 percent. Those figures come from clean samples with uniform particles. Real water with sediment, organic matter, and variable pH will perform worse, often substantially, until pretreatment is added.

Can I make or buy this powder for my home?

No verified consumer product exists as of November 2026. Chitosan itself is sold as a gardening and water-clarifying product, but not formulated or tested for microplastic removal at household scale. Anyone claiming a retail microplastic-removal powder should provide third-party lab results; absent those, treat the claim as unproven.

Why does pH matter so much for chitosan?

Chitosan's amine groups only carry a positive charge below roughly pH 6.5. Above that, the polymer loses its electrostatic grip on negatively charged plastic and binding efficiency falls. Most natural water sits at or above neutral pH, so field use requires acidification — an added cost and chemical handling step that lab tests avoid.

Is the magnetic nanoparticle part safe?

That is the open regulatory question. Nanoscale iron oxide can remain suspended if magnetic collection is incomplete, and published research flags the environmental fate of nanoparticles as unresolved. A commercial product would need filtration verification and regulatory review before release. The chitosan itself is biodegradable and low-risk.

How does this compare in cost to membrane filtration?

Membrane filtration removes over 95 percent of microplastics but carries high capital and energy costs plus fouling maintenance. Chitosan coagulation is cheaper per unit of water treated but removes less and produces sludge. The cost comparison depends on local sludge disposal prices and membrane capital costs, and no published study computes it for this specific powder.

What happens to the plastic once it is captured?

It becomes sludge. The flocs, plastic, chitosan, and iron oxide together form a waste stream that must be incinerated, landfilled, or processed. That disposal step carries cost and regulatory requirements, and it is the part of the process most often left out of popular coverage. Solving separation does not solve disposal.

Could this work in a river or lake cleanup?

Poorly, at scale. Open water has low microplastic concentrations, which makes the dose economics unfavorable — you would spread large amounts of powder to capture small amounts of plastic. The realistic application is at wastewater outfalls and treatment plants, where concentrations are higher and flow is controlled.